Elmomc SimplIQ Command Reference Manuel d'utilisateur Page 103
- Page / 188
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
0x8000 0x4000 0x2000 Meaning
0 0 0 OK.
0 0 1 Under voltage. The power supply is shut down or it
has too high an output impedance.
0 1 0 Over voltage. The voltage of the power supply is too
high, or the servo drive did not succeed in absorbing
the kinetic energy while braking a load. A shunt
resistor may be required.
0 1 1 Reserved.
1 0 0 Reserved.
1 0 1 Short circuit. The motor or its wiring may be
defective, or the drive is faulty.
1 1 0 Temperature. Drive overheating. The environment is
too hot, or lacks heat removal. There may be a large
thermal resistance between the drive and its
mounting.
1 1 1 Reserved.
Table 3-31: Bits 13 - 15 of MF Report
Attributes: Type: Status report, Integer, Bit-field
Scope: Program, RS-232, CANopen
Restrictions: None
Unit modes: All
Example:
The MF report of 0x3000 indicates that the motor has been shut down due to under
voltage. The under-voltage condition did not necessarily exist at the time the MF was
reported. It may possibly be the result of high power consumption and a high output
impedance of the power supply. In such a case, when the motor was shut down, the
power consumption stopped and the power supply returned to its normal voltage.
See also:
SR, MO, TS, LL[N], HL[N], CD, PE, VE
Reference chapter in the SimplIQ Software Manual:
Chapter 10, ”The Current Controller”
SimplIQ Command Reference Manual Alphabetical Listing
MAN-SIMCR (Ver. 4.5)
3-90
- SimplIQ 1
- Important Notice 2
- Contents 3
- Chapter 1: Introduction 6
- 1.2 Scope 7
- MAN-SIMCR (Ver. 4.5) 10
- Command Reference Manual 14
- Limit Ranges 16
- (Single_Turn+Multi_Turn) 17
- AC - Acceleration 19
- AG[N] - Analog Gains Array 20
- AN[N] - Analog Inputs Array 21
- SimplIQ electronics 22
- BG - Begin Motion 23
- BP[N] - Brake Parameter 25
- CA[N] - Commutation Array 28
- 16 - CA[34] 30
- 16-CA[34] 33
- CC - Compiled Program Ready 34
- CD - CPU Dump 35
- SimplIQ Software 37
- CP - Clear Program 39
- DC - Deceleration 40
- DD - CAN Controller Status 41
- DF/DS - Download Firmware 42
- DL - Download Program 43
- EC - Error Code 45
- SimplIQ internal use 53
- SimplIQ drive internal use 53
- EM[N] - ECAM Parameters 60
- EO - Echo Mode 62
- FF[N] - Feed Forward 65
- FR[N] - Follower Ratio 66
- GS[N] - Gain Scheduling 67
- SimplIQ can: 70
- HP - Halt Program Execution 73
- HX - Hexadecimal Mode 74
- IB[N] - Input Bits Array 78
- IF[N] - Digital Input Filter 80
- IL[N] - Input Logic 81
- SimplIQ drive will retry 82
- Harmonica drive has 6 86
- IP - Input Port 88
- JV- Jogging Velocity 90
- KI[N], KP[N] - PI Parameters 92
- KL - Kill Motion and Program 93
- LC - Current Limit Flag 95
- LL[N] - Low Feedback Limit 97
- LP[N] - List Properties 98
- LS - List User Program 99
- MF - Motor Failure 101
- MI - Mask Interrupt 104
- SimplIQ Software Manual: 105
- MO - Motor Enable/Disable 106
- MS - Motion Status 110
- OB[N] - Output Bits Array 111
- OC[N] – Output Compare 113
- OC[3]=100(RS), volatile 115
- OC[4]=200(RS), volatile 115
- OL[N] - Output Logic 116
- drive will receive 117
- OP - Output Port 118
- PA - Absolute Position 119
- PE - Position Error 120
- PK - Peak Memory 121
- SimplIQ Software Manual 122
- PM - Profiler Mode 124
- PP[N] - Protocol Parameters 125
- PR - Relative Position 127
- PS - Program Status 128
- PT - Position Time Command 129
- Notes: 131
- PX - Main Position 132
- PY - Auxiliary Position 133
- RG - Recorder Gap 136
- RL - Record Length 137
- RM - Reference Mode 138
- RP[N] - Recorder Parameters 139
- RS - Soft Reset 142
- RV[N] - Recorded Variables 143
- SD - Stop Deceleration 144
- SF - Smooth Factor 145
- SN - Serial Number 146
- SP - Speed for PTP Mode 147
- SR - Status Register 148
- ST - Stop Motion 150
- TC - Torque Command 152
- TM - System Time 154
- TR - Target Radius 156
- TS - Sampling Time 157
- TW[N] - Wizard Command 158
- UF[N] – User Float Array 159
- UI[N] – User Integer 160
- UM - Unit Mode 161
- VE - Velocity Error 163
- VR - Firmware Version 165
- 3-50 below 168
- 3-52 below 169
- 3-53 below 169
- XM[N] - X Modulo 175
- XP[N] - Extra Parameters 176
- YM[N] - Y Modulo 180
- Storage 182
- array · 3-9 183
Produits connexes et manuels pour Matériel Elmomc SimplIQ Command Reference
(118 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels