Elmomc SimplIQ Command Reference Manuel d'utilisateur Page 75
- Page / 188
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
HY[N] - Auxiliary Homing, Capture and Flag
Purpose:
Sets the parameters of the auxiliary homing and capture process, by which the
SimplIQ
sets a trap for a user-defined event. When the event occurs, the drive can:
Modify the auxiliary position counter (homing)
Log the exact position of the event (capture)
Flag a digital output (flag)
An event is a change in a digital input signal. The polarity of the change is defined by the
IL[N] command. Values in HY[3] are duplicated for compatibility reasons.
HY[N] (Index) Value Description
0 Disarm homing process. HY[1] is automatically reset to 0
when homing is complete.
1
Activation mode
1 Arm homing process. The sequence is activated according
to the last HY[2] to HY 6] values. HY[7] and HY[8] are
cleared.
2
Absolute value
Value to load, according to method of HY[5]. Absolute
value is limited to position counter range.
0 Immediate: Trigger is the receipt of HY[1]=1.
1/2 Event according to Auxiliary Home switch (capture).
3 High transition of Index pulse (capture).
4 Low transition of Index pulse (capture).
5/6 Event according to defined FLS switch.
7/8 Event according to defined RLS switch.
9/10 Event according to defined DIN1 switch.
11/12 Event according to defined DIN2 switch.
13/14 Event according to defined DIN3 switch.
15/16 Event according to defined DIN4 switch.
17/18 Event according to defined DIN5 switch.
3
Event definition
19/20 Event according to defined DIN6 switch.
21/22 Event according to defined DIN7switch.
23/24 Event according to defined DIN8 switch.
25/26 Event according to defined DIN9 switch.
27/28 Event according to defined DIN10 switch.
0 In UM=2, 3, 4, 5: stop immediately, using SD deceleration
value. In torque mode (UM=1), do nothing.
1 Set digital output, equivalent to OP=HY[6].
4
After-event
behavior. Defined
as the time in
which HY[1]
decreases to 0.
2 Do nothing.
SimplIQ Command Reference Manual Alphabetical Listing
MAN-SIMCR (Ver. 4.5)
3-62
- SimplIQ 1
- Important Notice 2
- Contents 3
- Chapter 1: Introduction 6
- 1.2 Scope 7
- MAN-SIMCR (Ver. 4.5) 10
- Command Reference Manual 14
- Limit Ranges 16
- (Single_Turn+Multi_Turn) 17
- AC - Acceleration 19
- AG[N] - Analog Gains Array 20
- AN[N] - Analog Inputs Array 21
- SimplIQ electronics 22
- BG - Begin Motion 23
- BP[N] - Brake Parameter 25
- CA[N] - Commutation Array 28
- 16 - CA[34] 30
- 16-CA[34] 33
- CC - Compiled Program Ready 34
- CD - CPU Dump 35
- SimplIQ Software 37
- CP - Clear Program 39
- DC - Deceleration 40
- DD - CAN Controller Status 41
- DF/DS - Download Firmware 42
- DL - Download Program 43
- EC - Error Code 45
- SimplIQ internal use 53
- SimplIQ drive internal use 53
- EM[N] - ECAM Parameters 60
- EO - Echo Mode 62
- FF[N] - Feed Forward 65
- FR[N] - Follower Ratio 66
- GS[N] - Gain Scheduling 67
- SimplIQ can: 70
- HP - Halt Program Execution 73
- HX - Hexadecimal Mode 74
- IB[N] - Input Bits Array 78
- IF[N] - Digital Input Filter 80
- IL[N] - Input Logic 81
- SimplIQ drive will retry 82
- Harmonica drive has 6 86
- IP - Input Port 88
- JV- Jogging Velocity 90
- KI[N], KP[N] - PI Parameters 92
- KL - Kill Motion and Program 93
- LC - Current Limit Flag 95
- LL[N] - Low Feedback Limit 97
- LP[N] - List Properties 98
- LS - List User Program 99
- MF - Motor Failure 101
- MI - Mask Interrupt 104
- SimplIQ Software Manual: 105
- MO - Motor Enable/Disable 106
- MS - Motion Status 110
- OB[N] - Output Bits Array 111
- OC[N] – Output Compare 113
- OC[3]=100(RS), volatile 115
- OC[4]=200(RS), volatile 115
- OL[N] - Output Logic 116
- drive will receive 117
- OP - Output Port 118
- PA - Absolute Position 119
- PE - Position Error 120
- PK - Peak Memory 121
- SimplIQ Software Manual 122
- PM - Profiler Mode 124
- PP[N] - Protocol Parameters 125
- PR - Relative Position 127
- PS - Program Status 128
- PT - Position Time Command 129
- Notes: 131
- PX - Main Position 132
- PY - Auxiliary Position 133
- RG - Recorder Gap 136
- RL - Record Length 137
- RM - Reference Mode 138
- RP[N] - Recorder Parameters 139
- RS - Soft Reset 142
- RV[N] - Recorded Variables 143
- SD - Stop Deceleration 144
- SF - Smooth Factor 145
- SN - Serial Number 146
- SP - Speed for PTP Mode 147
- SR - Status Register 148
- ST - Stop Motion 150
- TC - Torque Command 152
- TM - System Time 154
- TR - Target Radius 156
- TS - Sampling Time 157
- TW[N] - Wizard Command 158
- UF[N] – User Float Array 159
- UI[N] – User Integer 160
- UM - Unit Mode 161
- VE - Velocity Error 163
- VR - Firmware Version 165
- 3-50 below 168
- 3-52 below 169
- 3-53 below 169
- XM[N] - X Modulo 175
- XP[N] - Extra Parameters 176
- YM[N] - Y Modulo 180
- Storage 182
- array · 3-9 183
Produits connexes et manuels pour Matériel Elmomc SimplIQ Command Reference
(118 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels