Elmomc SimplIQ Command Reference Manuel d'utilisateur Page 46
- Page / 188
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Error
Code
Error String / Description
Example / Remedy
12 Command not available in this unit mode. PA=1000 is an error if UM=2,
because the position command
cannot be given in this mode.
13 Cannot reset communication – UART is
busy.
Modification of the parameters of the serial
communication has been attempted while
the communication line is busy.
18 Empty assign.
The right side of an equation is missing.
AC=; is an error because the
interpreter expects a numerical
value to appear after the = sign.
19 Bad command format.
An unresolved syntax error in the
command has occurred.
Refer to this manual for the
correct command syntax.
21 Operand out of range.
Assignment of an illegal value to a
parameter has been attempted.
JV=100,000,000 returns this error
because the required speed is
beyond the limits of the drive.
22 Zero division. JV=0; PX=1000/JV returns this
error.
23 Command cannot be assigned. BG=3000 returns this error
because BG is an execution
command that does not have a
value.
24 Bad operator.
An unrecognized character has been found
in an expression where an operator has
been expected.
IA[1]=3$VX is an error because $
is not a recognized operator.
25 Command not valid while moving. PV=n while in PVT motion is an
error because the PV=n
command sets the read pointer of
the PVT table manually; this
pointer is set automatically in
PVT mode.
26 Motion mode not valid.
A Begin Motion was attempted but the
parameters of the motion were not properly
set.
PV=n; BG is an error if the first
valid line of the PVT table is
smaller than the last valid line.
SimplIQ Command Reference Manual Alphabetical Listing
MAN-SIMCR (Ver. 4.5)
3-33
- SimplIQ 1
- Important Notice 2
- Contents 3
- Chapter 1: Introduction 6
- 1.2 Scope 7
- MAN-SIMCR (Ver. 4.5) 10
- Command Reference Manual 14
- Limit Ranges 16
- (Single_Turn+Multi_Turn) 17
- AC - Acceleration 19
- AG[N] - Analog Gains Array 20
- AN[N] - Analog Inputs Array 21
- SimplIQ electronics 22
- BG - Begin Motion 23
- BP[N] - Brake Parameter 25
- CA[N] - Commutation Array 28
- 16 - CA[34] 30
- 16-CA[34] 33
- CC - Compiled Program Ready 34
- CD - CPU Dump 35
- SimplIQ Software 37
- CP - Clear Program 39
- DC - Deceleration 40
- DD - CAN Controller Status 41
- DF/DS - Download Firmware 42
- DL - Download Program 43
- EC - Error Code 45
- SimplIQ internal use 53
- SimplIQ drive internal use 53
- EM[N] - ECAM Parameters 60
- EO - Echo Mode 62
- FF[N] - Feed Forward 65
- FR[N] - Follower Ratio 66
- GS[N] - Gain Scheduling 67
- SimplIQ can: 70
- HP - Halt Program Execution 73
- HX - Hexadecimal Mode 74
- IB[N] - Input Bits Array 78
- IF[N] - Digital Input Filter 80
- IL[N] - Input Logic 81
- SimplIQ drive will retry 82
- Harmonica drive has 6 86
- IP - Input Port 88
- JV- Jogging Velocity 90
- KI[N], KP[N] - PI Parameters 92
- KL - Kill Motion and Program 93
- LC - Current Limit Flag 95
- LL[N] - Low Feedback Limit 97
- LP[N] - List Properties 98
- LS - List User Program 99
- MF - Motor Failure 101
- MI - Mask Interrupt 104
- SimplIQ Software Manual: 105
- MO - Motor Enable/Disable 106
- MS - Motion Status 110
- OB[N] - Output Bits Array 111
- OC[N] – Output Compare 113
- OC[3]=100(RS), volatile 115
- OC[4]=200(RS), volatile 115
- OL[N] - Output Logic 116
- drive will receive 117
- OP - Output Port 118
- PA - Absolute Position 119
- PE - Position Error 120
- PK - Peak Memory 121
- SimplIQ Software Manual 122
- PM - Profiler Mode 124
- PP[N] - Protocol Parameters 125
- PR - Relative Position 127
- PS - Program Status 128
- PT - Position Time Command 129
- Notes: 131
- PX - Main Position 132
- PY - Auxiliary Position 133
- RG - Recorder Gap 136
- RL - Record Length 137
- RM - Reference Mode 138
- RP[N] - Recorder Parameters 139
- RS - Soft Reset 142
- RV[N] - Recorded Variables 143
- SD - Stop Deceleration 144
- SF - Smooth Factor 145
- SN - Serial Number 146
- SP - Speed for PTP Mode 147
- SR - Status Register 148
- ST - Stop Motion 150
- TC - Torque Command 152
- TM - System Time 154
- TR - Target Radius 156
- TS - Sampling Time 157
- TW[N] - Wizard Command 158
- UF[N] – User Float Array 159
- UI[N] – User Integer 160
- UM - Unit Mode 161
- VE - Velocity Error 163
- VR - Firmware Version 165
- 3-50 below 168
- 3-52 below 169
- 3-53 below 169
- XM[N] - X Modulo 175
- XP[N] - Extra Parameters 176
- YM[N] - Y Modulo 180
- Storage 182
- array · 3-9 183
Produits connexes et manuels pour Matériel Elmomc SimplIQ Command Reference
(118 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels