Elmomc SimplIQ Command Reference Manuel d'utilisateur Page 8
- Page / 188
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 2: Functional Listing
This chapter summarizes the Metronome commands according to the following
functional groups:
Motion Motion parameters, type and status. Begin/stop motion.
I/O Set outputs and report inputs.
Status Report Metronome status.
Feedback Support the multi-featured feedback interfaces.
Configuration Servo drive and motor types, and limitations.
Communication Communication type and parameters.
Control filters Digital, torque, speed and position filters.
Protections Failure and protection definitions.
Data recording Recording of internal Metronome variables for analysis.
User programs Application programming
General Miscellaneous commands.
Commands associated with more than one group are listed more than once.
2.1 Motion Commands
Command Description Page
AC Acceleration, in counts per second
2
3-6
BG Begin motion 3-10
BT Begin motion at defined time 3-13
DC Deceleration, in counts per second
2
3-27
IL[N] Input logic, defining how dedicated
inputs behave
3-68
JV Speed of jogging motion, in counts per
second
2
3-77
MO Motor on/off 3-93
PA Absolute position reference for point-to-
point motion
3-106
PR Relative position reference for point-to-
point motion
3-114
SD Stop deceleration 3-131
SF Smooth factor for motion command 3-132
SP Speed for point-to-point motion 3-134
ST Stop motion using deceleration value 3-137
TC Torque command 3-139
SimplIQ Command Reference Manual Functional Listing
MAN-SIMCR (Ver. 4.5)
2-1
- SimplIQ 1
- Important Notice 2
- Contents 3
- Chapter 1: Introduction 6
- 1.2 Scope 7
- MAN-SIMCR (Ver. 4.5) 10
- Command Reference Manual 14
- Limit Ranges 16
- (Single_Turn+Multi_Turn) 17
- AC - Acceleration 19
- AG[N] - Analog Gains Array 20
- AN[N] - Analog Inputs Array 21
- SimplIQ electronics 22
- BG - Begin Motion 23
- BP[N] - Brake Parameter 25
- CA[N] - Commutation Array 28
- 16 - CA[34] 30
- 16-CA[34] 33
- CC - Compiled Program Ready 34
- CD - CPU Dump 35
- SimplIQ Software 37
- CP - Clear Program 39
- DC - Deceleration 40
- DD - CAN Controller Status 41
- DF/DS - Download Firmware 42
- DL - Download Program 43
- EC - Error Code 45
- SimplIQ internal use 53
- SimplIQ drive internal use 53
- EM[N] - ECAM Parameters 60
- EO - Echo Mode 62
- FF[N] - Feed Forward 65
- FR[N] - Follower Ratio 66
- GS[N] - Gain Scheduling 67
- SimplIQ can: 70
- HP - Halt Program Execution 73
- HX - Hexadecimal Mode 74
- IB[N] - Input Bits Array 78
- IF[N] - Digital Input Filter 80
- IL[N] - Input Logic 81
- SimplIQ drive will retry 82
- Harmonica drive has 6 86
- IP - Input Port 88
- JV- Jogging Velocity 90
- KI[N], KP[N] - PI Parameters 92
- KL - Kill Motion and Program 93
- LC - Current Limit Flag 95
- LL[N] - Low Feedback Limit 97
- LP[N] - List Properties 98
- LS - List User Program 99
- MF - Motor Failure 101
- MI - Mask Interrupt 104
- SimplIQ Software Manual: 105
- MO - Motor Enable/Disable 106
- MS - Motion Status 110
- OB[N] - Output Bits Array 111
- OC[N] – Output Compare 113
- OC[3]=100(RS), volatile 115
- OC[4]=200(RS), volatile 115
- OL[N] - Output Logic 116
- drive will receive 117
- OP - Output Port 118
- PA - Absolute Position 119
- PE - Position Error 120
- PK - Peak Memory 121
- SimplIQ Software Manual 122
- PM - Profiler Mode 124
- PP[N] - Protocol Parameters 125
- PR - Relative Position 127
- PS - Program Status 128
- PT - Position Time Command 129
- Notes: 131
- PX - Main Position 132
- PY - Auxiliary Position 133
- RG - Recorder Gap 136
- RL - Record Length 137
- RM - Reference Mode 138
- RP[N] - Recorder Parameters 139
- RS - Soft Reset 142
- RV[N] - Recorded Variables 143
- SD - Stop Deceleration 144
- SF - Smooth Factor 145
- SN - Serial Number 146
- SP - Speed for PTP Mode 147
- SR - Status Register 148
- ST - Stop Motion 150
- TC - Torque Command 152
- TM - System Time 154
- TR - Target Radius 156
- TS - Sampling Time 157
- TW[N] - Wizard Command 158
- UF[N] – User Float Array 159
- UI[N] – User Integer 160
- UM - Unit Mode 161
- VE - Velocity Error 163
- VR - Firmware Version 165
- 3-50 below 168
- 3-52 below 169
- 3-53 below 169
- XM[N] - X Modulo 175
- XP[N] - Extra Parameters 176
- YM[N] - Y Modulo 180
- Storage 182
- array · 3-9 183
Produits connexes et manuels pour Matériel Elmomc SimplIQ Command Reference
(118 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels